How to Build a Bottle Rocket: Simple Step-by-Step Instructions (2024)

  • Categories
  • Arts and Entertainment
  • Fireworks
  • Model Rockets

Download Article

Two different kinds of bottle rocket designs to soar into the sky

Co-authored byJessie Antonellis-Johnand Luke Smith, MFA

Last Updated: September 8, 2024Fact Checked

Download Article

  • Simple Rocket
  • |
  • Launching Your Rocket
  • |
  • Double-Bottle Rocket
  • |
  • Video
  • |
  • Expert Interview
  • |
  • |
  • Warnings

You’re never too young to be an astronaut! You might not be making a trip to the moon for a few more years, but you can launch your very own rocket right in your backyard. We’ll show you how to build and launch a simple bottle rocket out of supplies you have at home. Then, we’ll show you how to make a slightly more advanced rocket that’ll fly even higher. Put on your safety goggles and prepare for liftoff!

Method 1

Method 1 of 3:

Making a Simple Bottle Rocket

Download Article

  1. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (5)

    1

    Roll a piece of construction paper into a cone and cover it with duct tape. Roll the construction paper along the long edge, overlapping the corners to form a cone shape. Use a piece of duct tape to secure the cone so that it doesn’t unroll. Then, cover the rest of the cone in duct tape to make it more durable.[1] This is the nose of your rocket, which will make it more aerodynamic, helping it fly farther.

    • To make your rocket a bit safer, tape one half of a plastic egg over the tip of the cone, which gives it a blunt tip that won’t hurt anyone when it falls.
  2. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (6)

    2

    Tape the nose cone to the bottom of a 2-liter (68 fl oz) soda bottle. Position the cone over the base of the bottle, then use duct tape to fix it in place.[2] Do your best to tape it onto the bottle as straight as possible, taking care not to make it crooked, which might make it so that the rocket doesn’t fly as straight.

    Advertisement

  3. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (7)

    3

    Cut out 4 cardboard triangles and tape them around the center of the bottle. Use scissors to cut triangles out of cardboard, making each triangle about 4 inches (10cm) wide and 7 inches (18cm) long. These are the fins of the rocket, which stabilize it in the air. Then, use duct tape to attach the fins around the nozzle of the bottle, so that they point toward the cone. Place a bit of duct tape on either side of each fin, and evenly space them around the bottle.[3]

    • To make sure your rocket can stand on its own when you launch it, attach the fins so that they extend about 2–3 inches (5.1–7.6cm) past the nozzle of the bottle.
    • To help you evenly space the fins, tape the first fin anywhere around the nozzle of the rocket. Then tape the second fin on the opposite side of the bottle. Tape your third fin between those two, and the fourth fin opposite the third fin.
  4. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (8)

    4

    Tape Play-Doh or clay around the nozzle of the bottle to add weight. Roll a bit of clay into a log about 1 inch (2.5cm) thick, then wrap it around the bottle’s nozzle and use duct tape to secure it in place. This the is the “ballast” of the rocket, which adds weight that helps stabilize the rocket.[4]

    • Alternatively, tape 5-10 quarters or other coins around the nozzle of the bottle to add weight.
  5. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (9)

    5

    Fill the bottle halfway with water. Pour about 1 liter (0.26USgal) of water into the bottle. When you launch your rocket, you’ll pump air into the inside with a bicycle pump. Then, the water will trap the air inside until the bottle can’t hold any more air. The pressure pushes all the water out the bottom, providing enough force to launch the rocket![5]

  6. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (10)

    6

    Poke a hole through a cork and place the cork in the bottle’s nozzle. Use a nail to make a small hole through the center of a cork. Hold the nail with pliers to avoid injuring yourself. Then, stuff the cork into the nozzle of the bottle.[6] Make sure not to cover the cork’s hole with tape, though.

  7. Advertisement

Method 2

Method 2 of 3:

Launching Your Rocket

Download Article

  1. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (12)

    1

    Insert the needle of a bicycle pump into the hole in the cork. Use a standing bicycle pump, the kind that has a lever you push down on to inflate a tire. Screw the needle attachment to the nozzle of the pump, then push the needle into the hole in the cork of your bottle rocket.[7]

  2. 2

    Stand the rocket on its fins on a flat surface. Find a level surface, like a sidewalk or the asphalt of a parking lot, to launch your rocket. Or, launch it in the center of a yard or a park, laying down a piece of cardboard for a flat surface. With the bike pump attached to the cork, stand the rocket upright, using its fins to keep it steady.[8]

    • Make sure there’s nobody else around when you launch the rocket to avoid hurting someone when it falls back down to earth. Also make sure there are no windows or breakable objects nearby.
  3. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (14)

    3

    Quickly pump the lever of the bike pump to shoot your rocket. Stand next to the bike pump and work the lever up and down rapidly to fill the rocket with air. Watch the bubbles rise through the water inside the rocket, adding pressure to the inside. Keep pumping until the rocket gathers enough pressure and achieves liftoff![9]

    • The water will shoot out everywhere when the bottle rocket takes off, so be prepared to get a bit wet.
    • Your rocket blasts off because the force off the water and air exiting through the nozzle pushes it off the ground.
    • Be cautious once you start pumping and do not approach the rocket, even if it appears that nothing is happening with the launch, as this can lead to injury.
  4. Advertisement

Method 3

Method 3 of 3:

Making a Double-Bottle Rocket

Download Article

  1. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (16)

    1

    Grab two 2-liter (68 fl oz) bottles and cut off the cap end of one bottle. Use scissors or a box cutter to remove the top ⅓ of a plastic bottle. Work slowly and carefully to make sure you don’t hurt yourself, and that the cut is as neat as possible. Cut a soda bottle that’s slightly larger than the second, intact bottle so that you can tape them together later. Keep your second 2-liter (68 fl oz) bottle intact.[10]

    • Cutting off the cap end of the bottle will make the rocket more aerodynamic and durable. A rounded end is also softer so it will do less damage to any objects if the rocket hits something when it lands.
  2. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (17)

    2

    Stuff clay or newspaper into the cut bottle to add weight. Place a golf-ball sized wad of clay or Play-Doh into the bottom of the cut bottle. Or, wad up a few pages of newspaper and place it in the bottom of the bottle. This is the ballast of your rocket, which will add weight and help the rocket stay stable in the air.[11] Secure the ballast inside the bottle with duct tape.

    • Or, pour 10-12 pennies into the bottom of the cut bottle as your ballast, and hold them in place with duct tape.
  3. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (18)

    3

    Place the intact bottle inside the cut bottle and tape them together. Insert the bottom of the intact bottle into the opening of the cut bottle that holds the ballast. Make sure the bottles overlap by about 2–3 inches (5.1–7.6cm), then secure them together by wrapping a generous amount duct tape around where they meet.[12]

  4. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (19)

    4

    Cut 4 triangles out of cardboard and fix them to the bottles with duct tape. Use scissors to cut out 4 triangles that are 4 inches (10cm) wide and 7 inches (18cm) long. Then, secure them around the taped-together bottles, toward the nozzle, with duct tape, making sure they’re evenly spaced. These are the fins of your rocket, which will make it fly straighter through the air.[13]

    • To make sure your rocket can stand on its own when you launch it, attach the fins so that they extend about 2–3 inches (5.1–7.6cm) past the nozzle of the rocket.
  5. 5

    Fill the intact bottle halfway with water. Add 1 litre (34floz) of water to the bottle. You’ll launch your rocket by pumping it full of air with a bike pump. The water will trap the air inside until the bottle can’t hold anymore air. The pressure will pop the cork off the end and shoot the water down at the ground, propelling the rocket into the air.[14]

  6. How to Build a Bottle Rocket: Simple Step-by-Step Instructions (21)

    6

    Poke a small hole in a cork and insert the cork into the bottle’s nozzle. Use a nail to make a hole through the center of a cork. Wear gloves or use pliers to hold the nail to avoid injuring yourself. Then, squeeze the cork into the nozzle of the bottle. Make sure it’s secure![15]

  7. Advertisement

Expert Q&A

Search

Add New Question

  • Question

    How do I make a Mentos soda bottle rocket?

    Jessie Antonellis-John
    Math and Science Instructor

    Jessie Antonellis-John is a Math and Science Instructor who teaches at Southwestern Oregon Community College. With over 10 years of experience, she specializes in curriculum development. Jessie earned her PhD in Teaching & Teacher Education from the University of Arizona, her Master of Education from Western Governors University, and her BS in Astrophysics from Mount Holyoke College. She’s also co-authored several peer-reviewed journal articles in professional publications.

    Jessie Antonellis-John

    Math and Science Instructor

    Expert Answer

    To make a Mentos soda bottle rocket, you'll need a two-liter soda bottle, a roll of Mentos candies, and a piece of paper. First, carefully open the soda bottle and drink or pour out some of the soda to create space. Roll the paper into a tube and fill it with Mentos candies. Quickly drop the Mentos-filled tube into the soda bottle, screw the cap on tightly, turn the bottle upside down, and place it on a flat surface. Once you're ready for the launch, unscrew the cap, and the reaction between the Mentos and soda will create a fizzy eruption, propelling the bottle into the air. Make sure to do this outdoors and wear protective gear.

    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support wikiHow

    YesNo

    Not Helpful 9Helpful 11

  • Question

    Is this safe for school?

    How to Build a Bottle Rocket: Simple Step-by-Step Instructions (24)

    Community Answer

    Yes. In fact, bottle rockets are a common school science project!

    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support wikiHow

    YesNo

    Not Helpful 437Helpful 1136

  • Question

    What kind of bottle do I have to use?

    How to Build a Bottle Rocket: Simple Step-by-Step Instructions (25)

    Community Answer

    A good type of bottle would just be a regular 1L soda bottle such as a Coke bottle.

    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support wikiHow

    YesNo

    Not Helpful 323Helpful 615

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

      Advertisement

      Video

      Tips

      Submit a Tip

      All tip submissions are carefully reviewed before being published

      Name

      Please provide your name and last initial

      Submit

      Thanks for submitting a tip for review!

      Warnings

      • Wear safety goggles or other eye protection when you launch your rocket. Good science requires proper safety!

        Thanks

        Helpful2Not Helpful1

      • Have an adult help you use any sharp tools like scissors or box cutters to avoid injury.

        Thanks

        Helpful2Not Helpful1

      Advertisement

      Things You'll Need

      Simple Bottle Rocket

      Launching Your Rocket

      Double-Bottle Rocket

      You Might Also Like

      How toMake Sugar RocketsHow toMake a Diet Coke and Mentos Rocket
      How toMake a Simple RocketHow toMake a Baking Soda and Vinegar RocketHow toMake a Match RocketHow toMake a Water RocketHow toMake a RocketHow to Make a DIY Paper Rocket That Flies FarHow toMake a Powerful Air Pressure RocketHow toMake a Mini Rocket

      Advertisement

      Expert Interview

      Thanks for reading our article! If you’d like to learn more about model rockets, check out our in-depth interview with Jessie Antonellis-John.

      More References (6)

      About This Article

      How to Build a Bottle Rocket: Simple Step-by-Step Instructions (33)

      Co-authored by:

      Jessie Antonellis-John

      Math and Science Instructor

      This article was co-authored by Jessie Antonellis-John and by wikiHow staff writer, Luke Smith, MFA. Jessie Antonellis-John is a Math and Science Instructor who teaches at Southwestern Oregon Community College. With over 10 years of experience, she specializes in curriculum development. Jessie earned her PhD in Teaching & Teacher Education from the University of Arizona, her Master of Education from Western Governors University, and her BS in Astrophysics from Mount Holyoke College. She’s also co-authored several peer-reviewed journal articles in professional publications. This article has been viewed 2,163,257 times.

      72 votes - 70%

      Co-authors: 266

      Updated: September 8, 2024

      Views:2,163,257

      Categories: Featured Articles | Model Rockets

      Article SummaryX

      To build a bottle rocket, start by rolling a piece of paper into a cone and covering the outside of it with duct tape. Then, attach the cone to the bottom of an empty plastic bottle and cut out 4 cardboard triangles to make your rocket's fins. Attach the cardboard to the bottle and then fill up the bottle with water. Once you've done that, poke a hole in a cork and plug the opening of the bottle with it. Finally, attach a bicycle pump valve to the cork. To learn how to launch your bottle rocket, scroll down!

      Did this summary help you?

      In other languages

      Spanish

      Portuguese

      Dutch

      French

      Russian

      Chinese

      Indonesian

      Korean

      Arabic

      Turkish

      Hindi

      • Print
      • Send fan mail to authors

      Thanks to all authors for creating a page that has been read 2,163,257 times.

      Reader Success Stories

      • How to Build a Bottle Rocket: Simple Step-by-Step Instructions (34)

        Mike Blair

        Aug 12, 2022

        "With as dry as the midwest has been, it would have been a bad idea to use class C motors (fire hazard), so using a..." more

        Rated this article:

      More reader storiesHide reader stories

      If you buy through links on our site, we may earn a commission.

      Did this article help you?

      Advertisement

      How to Build a Bottle Rocket: Simple Step-by-Step Instructions (2024)
      Top Articles
      Latest Posts
      Recommended Articles
      Article information

      Author: Chrissy Homenick

      Last Updated:

      Views: 6784

      Rating: 4.3 / 5 (74 voted)

      Reviews: 81% of readers found this page helpful

      Author information

      Name: Chrissy Homenick

      Birthday: 2001-10-22

      Address: 611 Kuhn Oval, Feltonbury, NY 02783-3818

      Phone: +96619177651654

      Job: Mining Representative

      Hobby: amateur radio, Sculling, Knife making, Gardening, Watching movies, Gunsmithing, Video gaming

      Introduction: My name is Chrissy Homenick, I am a tender, funny, determined, tender, glorious, fancy, enthusiastic person who loves writing and wants to share my knowledge and understanding with you.